Results 1 to 4 of 4

Thread: Help mounting Harness

                  
   
  1. #1

    Help mounting Harness

    Hello,

    I am about get harness for my 89 325i. I do not have any roll bars or roll cage. I will be also replacing my seats to Corbeau racing seats. Do you know how these should be mounted?

    Here is a picture of the harness I am getting.
    http://www.apexperformance.net/cartg...?pid=37&cid=13 You can click on the picture to enlarge it.

    Also, does anyone know if there should be any mounting tools or kits for a Corbeau seat with a bracket? Here is the seat I am getting.
    http://www.store.yahoo.com/racingsup.../cofoiibl.html

    Thanks alot

  2. #2
    Senior Member
    Join Date
    Jun 2004
    Location
    Evil Commonwealth
    Posts
    226
    You CANNOT do it without a rollbar/rollcage/harness bar. The angles of the harnesses, no matter what you do, would be improper. They could actually cause you more injury than help you. Notwithstanding the problems associated with having a fixed back seat and wearing harnesses in the event that your car flips over.

    You should also purchase the seat from www.apexperformance.net : Ask to speak with linda powell and tell her James Derry referred you from bimmerforums. She will make you a better deal on the corbeau seats and harnesses. Trust me.

    Your best bet, would be to purchase schroth clip-in harnesses (www.hmsmotorsports.com) -- Linda also sells these; but, hms has a better write-up about them (not sure if they make them for your car though -- I think they do).

    I would not run the five points like you are thinking without at minimum, a harness bar.

    To pre-empt your questions:

    a) I do not believe anyone makes purely a harness bar for your car. They might, I remember brey-krause makes harness bars; but, not sure if its for an E30. Otherwise, you'll have to get it custom done. I would recommend Kearney Racing.

    b) a 4 point roll bar would be better. You can buy a four point from kirk racing in AL and ship it. Should be less than $500 total. Ask to speak with Linda. www.kirkracing.com

    c) could have a custom 4 point made for around $1K-$1300.
    Last edited by NoSoup4U; 03-18-2005 at 09:35 AM.

  3. #3
    Thank you so much for your reply. Very helpful. I actually purchased both the seats and harness from Linda at Apex Performance. She gave me a good deal on the Harnes. Let's see, I may have to call now and do something else about the harness.


    Thanks again.

  4. #4
    Banned
    Join Date
    Jan 2005
    Location
    Clifton, VA
    Posts
    570

    Harness Bars

    I have heard of harness bars collapsing. Would never trust one at drivers school.
    You need a bar or cage. Know a student and an instructor who were saved by the fact the car did not have harnessess when the E36 coupe rolled over. Old timers know the incident I am talking about. The roof partially collapsed and the fact their seat belts allowed them to move probably saved their lives and prevented serious neck and back problems. They walked away. There are serious g loads generated in any accident at the track. Drivers have been decapitated by sheet of paper in high g load accident.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Why you should wear a helmet support - PCA fatality at the Glenn
    By SharkD in forum HPDE sponsored by Specr53.com
    Replies: 26
    Last Post: 08-17-2005, 06:16 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •