Printable View
I am thinking about changing my shocks/struts and springs. Will I have enough time to change shocks/struts and springs on a 2001 330Ci during a DIY event? If so, is there a special tool that I'd need to buy? Will installing the camber plates add significant time?
Thanks all.
Based on your question, the answer is probably not, unless you bring a good mechanic along to help you.
Perhaps you should register for an upcoming DIY as a helper, and learn your mechanical boundaries in relation to DIY time constraints. This is the way quite a few current working members have gotten into the Chapter DIY program.
Hope this helps.
Alan :tongue:
DIY Chair
Thanks for the advice Alan. The last DIY event I went to I changed my rear brake pads and fuel filter. I'll probably start small. I'll go the next event and change my sway bars. I have Bentley manual and it doesn't look too bad. Hopefully with the help of more experienced fellow members it's something doable :biggrin:.
Unrelated to DIY's but some advice:
If you're changing struts/springs/camber plates, you can pre-assemble them so that you only need to unbolt the stock units and bolt in the aftermarket parts. The most time consuming part is compressing the springs and re-assembling the struts when you have to re-use an oem part (strut hat, spring, or strut). Fronts can be done under an hour on a lift, rears take about 30 minutes if you can find someone to help you that's done it before. You'll need an alignment afterwards...but you probably knew that.
This is very true. I'm in the process of changing them on my E39 and just realized since I'm replacing everything I could have had the whole new strut assembled and ready for when I took the old one out. Good point Craig!Quote:
Originally Posted by Car54
Dont know the E46 setup, but getting the balljoint out is the most time consuming part for me. Waiting for a BMW tool. But the E39 has a little different setup than the 3 series.
The E46 requires no balljoint work. The front strut is clamped to the knuckle.Quote:
Originally Posted by Scany
That said, if you're looking to install lowering springs on the car, don't. The E46 is *badly* front suspension travel limited, and taking away from this travel hurts the ride quality a lot - not because the srpings are stiffer, but because you end up all over the bump stop.
Even M3's Nick?
You are presuming that the owner is buying new strut housings? In an upgrade like this, I think you only need to change the springs and dampers. If so, you can't assemble the new struts until the old ones are out...Quote:
Originally Posted by Car54
Yes.Quote:
Originally Posted by Car54
Seeing as how he has an E46, the bit about new strut housings was pretty much implied. :pQuote:
Originally Posted by Scotty
I'm not presuming, he said shocks/struts and springs....and then asked about camber plates. That's all you have in the assembly....if he replaces all that, he can build an assembly away from the car to install at a later date and then keep his stock setup assembled.
You are right, I have received the front Koni struts and it came with strut housing and all. I just changed all four tires and noticed that if I could pre-assemble everything it didn't look too bad. The rear shocks seemed a lot easier to change than the fronts. I have the springs, shocks and struts and about to order the Vorschlag camber plates and rear M3 RSM, so I probably just need to order the bump stops and the boots, I should have everything and be able to pre-assemble them ahead of time. Hmm...thinking...:confused:.Quote:
Originally Posted by Car54
I can probably start by changing the sway bars and take it from there.
My front springs (TCK 450lb, std. length, whatever that is...6"?) show signs of coil bind. My choices seem to be bottoming out on the bump stop or getting coil bind. I now set the compression on the front to very stiff to keep either from happening. I have a picture of me in a turn and the front right is really compressed, indicating 450lb spring are just not enough for this car. At VIR North, the transition to the north course requires full stiff to keep me from banging.Quote:
Originally Posted by Nick325xiT 5spd
EDIT: I'm talking about an E46 M3.
Have you trimmed the bump stop?Quote:
Originally Posted by Rod
Edit: And have you considered running stiffer springs?
No, YesQuote:
Originally Posted by Nick325xiT 5spd
I don't want to trim the bump stops, and stiffer springs, say 600lb, is what I'd love to have, but it's my DD. I don't think less than 600lb would make big enough of a difference for the problem, and any more that my current 450lb would be tough on the street. More travel would be the ideal solution, ha!
Trim the bump stops. Take about half an inch off the top (non-tapered) part. Seriously - everyone does that with the TCKRs.Quote:
Originally Posted by Rod
Also, just stepping the front up to 500lbs. would yield an 11% increase in load bearing. That's not insignificant - it's equivalent to raising your car .33 inches if you run the same height. Personally, I'd trim the bump stop and up the rate to 500lbs. You clearly need it.
I feel like I should edit my post to include a link now. :)Quote:
Originally Posted by Car54
I deleted my post...nice reply