Installing 3 point stock belts after installing race seats

[jfraymond]

Hello my fellow BMW Brothers and Sisters!

I recently installed racing seats with 6 point harnesses in my 2012 e92 M3. I need to install my stock belts to pass inspection and am wondering if anyone has done this or can recommend a good way to put my stock belts back in the car. I'm not planning to use the stock belts, they just have to function so that the car passes inspection.

Thanks!

If you're referring to the biannual MD VEIP emissions inspection, then I really doubt that the Maryland VEIP technicians will care. But to make sure, take the car to a self-service VEIP kiosk and complete the emissions test yourself. It's simple - all you do is plug their OBDII cable into the OBDII port under your car's dashboard and let their machine read your car's computer for emissions-related fault codes. Any car (under 8,500 lbs GVWR) built in 2005 or later can be taken to the VEIP self-service kiosk. See http://www.mva.maryland.gov/programs...kFlyer2016.pdf

Since you already own this car, I presume that it's registered and titled to you and therefore you already had the Maryland safety inspection done when you acquired the car. If you just acquired the car and installed the 6-point harnesses before having the MD safety inspection done (required to register and title the car), then you may have to re-install the factory seat belts to pass the safety inspection.

So, to which inspection are you referring?

Good luck!

[VikAry]

If you're referring to the biannual MD VEIP emissions inspection, then I really doubt that the Maryland VEIP technicians will care. But to make sure, take the car to a self-service VEIP kiosk and complete the emissions test yourself. It's simple - all you do is plug their OBDII cable into the OBDII port under your car's dashboard and let their machine read your car's computer for emissions-related fault codes. Any car (under 8,500 lbs GVWR) built in 2005 or later can be taken to the VEIP self-service kiosk. See http://www.mva.maryland.gov/programs...kFlyer2016.pdf

Since you already own this car, I presume that it's registered and titled to you and therefore you already had the Maryland safety inspection done when you acquired the car. If you just acquired the car and installed the 6-point harnesses before having the MD safety inspection done (required to register and title the car), then you may have to re-install the factory seat belts to pass the safety inspection.

So, to which inspection are you referring?

Good luck!

Thank for the feedback. I do own the car and it passed inspection 4 years ago when I bought it. I was preparing for possible re-inspection because I may not pass Emissions and as a result, my registration will be suspended. But thank you for bringing up the dreaded Emissions test. My car is heavily modified for the track, tuned, completely catless and I drive 500-750 street miles per year, at most. A couple of weeks noticed the Service Engine light which had never come on before. Knowing that I had to pass Emissions soon, I used my Carly BMW App to clear all of my fault codes but after running the Emissions test in the App, it showed that the following sensors are not in "ready" state (incomplete) - Catalyst, Evaporative, Secondary Air, O2 Sensor, O2 Heat Sensor and EGR/VVT System.

After clearing the fault codes, I thought I could pass Emissions and so I used the self service kiosk in Gaithersburg to test Emissions. The readiness report says that multiple diagnostic systems in my car are not ready, which I didn't expect because I've cleared all the codes from the car's computer. MVA has instructed me to have the car tested at a full service station to and I'm expecting the same result which will result in a 30-day extension to get the car in ready state. I'm aware of the BMW FTP Drive Cycle which is supposed to ready the systems that have issues but trying to execute that on a public road is going to be near impossible. So, I'm wondering if replacing the battery would reset the systems. My battery warning light also came on around the same time as the Service Engine warning.

Any guidance or advice to help me pass Emissions would be appreciated.

[jfraymond]

Any guidance or advice to help me pass Emissions would be appreciated.

Your ECU "knows" if any fault codes have been recently cleared, and the VEIP emissions test detects this as well. You'll need to put some miles on the car, and start and stop the engine a number of times, before the ECU thinks that it's "ready" for the emissions test.

Here's the good news: under Maryland law, if you fail the emissions test, you're only required to spend a maximum of $450 (with a MD licensed mechanic / shop) to try to address the problem. You'll need your repair receipts showing that you tried to have the emissions issues fixed. If the car still fails the test, you can get a VEIP emissions waiver. See http://www.mva.maryland.gov/programs...veipwaiver.htm
As long as you follow the guidance on that State of Maryland VEIP web page, you should be fine. I've done this; it worked.

Do you still drive this car on the street? If it's a track-only car that you tow to the track, then you can cancel the registration, return the license plates to MVA, and be off the hook with regards to emissions testing.

Let us all know how it works out! Again, good luck.